FLYBACK CALCULATIONS - PART VI

In this part we will calculate the RMS current ripple in the main output filter capacitor.

First we need to calculate the main output secondary current using the following data:

Idrms = 0.2 A
Dmax = 0.85
VRO = 350 volts
KL = 1.0
VF1 = 1.0 volt
Vo1 = 14 volts

where Idrms is the rms transistor switch current, Dmax is the maximum allowable duty cycle (usually limited by the main PWM control IC), VRO is the secondary voltage reflected to the primary side, Vo1 is the nominal output voltage, VF1 is the forward voltage of the output diode, and KL is the load occupying factor for the main output (1.0 if there is only one output winding.)

The equation for the secondary RMS current is

Isecrms = Idsrms * (((1 - Dmax) / Dmax )^0.5) * VRO * KL / (Vo1 + VF1)

Isecrms = 1.96 A

The output current Io is specified as 0.3 amps, so now we can calculate the output capacitor ripple current. This current is usually inconveniently large for flyback converters and cheap converters are sometimes found to have an output filter capacitor that is under-rated for ripple current. The risk is that the capacitor will overheat, dry-out too fast and the converter will fail to operate as intended. The ripple current is calculated as follows:


Icaprms = ( Isecrms^2 - Io^2 )^0.5

Icaprms = 2.28 A

Note that a continuous current mode (CCM) converter will have a lower secondary RMS current for a given output current load.

So we will need to have a capacitor that is rated at 2.3 amps or better for this design. It is better to use one large capacitor instead of smaller capacitors in parallel to meet the current requirement as parallel capacitors will not necessarily share ripple current equally and one or more of them could overheat. It is usually good though to put small capacitors in parallel such as ceramic chip caps for filtering high frequency noise.

Assume that we have the additional data as follows:


Co = 330UFD

Rc = 0.07 ohm

Idspeak = 0.3 A

Fs = 100KHZ

where Co is the output filter capacitance total, Rc is the equivalent series resistance of the capacitance, Idspeak is the peak transistor switch current, and Fs is the converter switching frequency.

Now we can calculate the theoretical output ripple or noise voltage using the equation

dVo1 = Io * Dmax / (Co * Fs ) + Idspeak * VRO * Rc * KL / (Vo1 + VF1 )

dVo1 = 0.498 volts

On an output voltage of 14 volts, 0.498 volts is about 3.6%. This value is probably OK for a battery charger converter, but probably too high if the voltage is to be used to power some electronic circuit. For a lower output ripple voltage, it would be necessary to increase capacitance value, reduce the equivalent series resistance of the capacitor, or both. Notice that the above calculation ignores the effects of the capacitor series inductance and the inductance of the circuit wires or circuit board traces. A low inductance layout is very important to keep noise low.

AC-DC FLYBACK CALCULATIONS - PART V

One of the most important things to determine on the AC-DC flyback converter are the RMS secondary winding currents. The RMS current must be filtered by a capacitor which is usually an aluminum electrolytic capacitor or some type of large capacitance high ripple current capable capacitor. One of the main failure modes of poorly designed flyback converters is an inadequate current rating for the filter capacitors. If the output capacitor is over-stressed with ripple current beyond its ratings it will run hot, dry out if it is a wet electrolytic, and otherwise fail casuing converter failure.

We can calculate the RMS current for each secondary winding according to a simple formula as follows:

Isecrms = Idsrms * (( 1 - Dmax ) / Dmax )^0.5 * VRO * KL / ( Vo1 + Vf1 )

where we have previously calculated the rms switch current Idsrms = 0.234 A, VRO = 349 volts, and we have specified Vo1 = 14 volts, Vf1 = 1 volts, and the load occupying factor KL has been set to 0.8 or 80% of the total load on the Vo1 output.

The answer is then that Isecrms = 1.8 amps. This is not a trival amount of ripple current to deal with and it will require a large electroylitic capacitor or several capacitors in parallel to handle the current. Note that it is difficult to parallel capaciotrs to handle the total load because one capacitor will more than likely try to handle most of the load and overheat while the other ones are not handling their share.

Another thing to be concerned about in flyback converters is the rating of the diode that feeds current to the filter capacitor from the secondary winding (see Fig. 1 -click on the figure for a larger view.) The current rating of the diode must be able to handle the RMS current we just calculated above and it must have a high enough voltage rating to handle the reverse spikes which are present on every switch cycle of the converter. We can calculate the reverse voltage on the diode from the following formula:

Vdr = Vo1 + Vdcmax * ( Vo1 + Vf1 ) / VRO

where Vo1 is the output DC voltage, 14V, Vdcmax is the max input voltage, 1000V,
Vf1 is the forward diode voltage, 1 volt, and VRO is the voltage reflected from secondary to primary on each switch cycle, 349 volts.

Vdr = 56.9 volts

is the peak reverse voltage on the diode.

It is customary to comput the VRRM (the voltage rating reverse maximum value) as

VRRM = 1.3 * Vdr = 74 volts

The VRRM value we computed is beyond the normal max for schottky diodes of 45 volts but there are some hybrid schottkys that will rate higher. The advantage of schottky diodes is that they have a lower forward voltage drop and therefor dissipate less heat and power for a given current load. If the output voltage had been 5 volts instead of 14, we could then have used a 35V or 45V schottky diode as VRRM would have calculated to 29 volts.

FLYBACK CALCULATIONS - PART IV

In all switchmode converters that use a high frequency switching inductor or transformer, such as the typical AC-DC flyback converter shown if Fig. 1, it is of critical importance to avoid saturation of the inductor or transformer. If saturation occurs, the inductance of the transformer or inductor will decrease greatly so that the windings will no longer support the applied voltage. If saturation occurs when the transistor switch is in the on-state, the switch current is theoretically unlimited and this could lead to destruction of the converter. Even when current mode control is used, the initial turn-on spike will be so large that it most likely will cause the switch to fail.

To avoid going into saturation, the transformer must be designed so that at maximum current (set by the current limit), the transformer or inductor will not saturate. Therefore we need to determine the maximum magnetic field density (flux density) that the transformer core material will support (carefully the core manufacturer's data sheet), the effective cross-sectional area of the core, the inductance of the inductor or the primary of the transformer, and the maximum current set by the current limit. Then we must calculate the minimum number of inductor or primary turns that will be required to avoid saturation. The number of turns required is directly proportional to the product of the inductance and the maximum current and inversely proportional to the product of the maximum flux density and the core area.

Npmin = Lm * Ilim * 10^6 / ( Bsat * Ae )

Let

Lm = 0.007 Henry

Ilim = 0.200 Ampere

Ae = 31.5 mm^2

Bsat = 0.25 Tesla ( 2500 Gauss )

Then

Np = 187 turns ( rounded up to the nearest full turn )

The actual design might use 225 turns to provide a safety factor of approximately 20%.

Once we have set the primary turns, we can then calculate the turns ratio that is needed to achieve the required main output (the controlled output) voltage as


n = VRO / ( Vo1 + vf1 )


Let

VRO = 350 volts

Vo1 = 15 volts

Vf1 = 1 volt

where VRO is the reflected voltage from secondary to primary (previously calculated in the post, Flyback Calculations - Part I), Vo1 is the required main output voltage, and Vf1 is the forward voltage of the output rectifier diode at maximum output current. Then

n = 22 (rounded to an integer)

Now it is easy to compute the required turns of the main secondary, as


Ns1 = Np / n = 10 (rounded to the closest integer)

The other secondary output turns can now be computed using the values from the equation

Nox = ( Vox + Vfx ) * Ns1 / ( Vo1 + Vf1 )

where Nox is the required secondary turns, Vfx is its diode forward voltage at the winding's maximum current. For example if Vox is 125 volts and Vfx is 1.2 volts, we have

Nox = 81 turns (rounded up to the nearest integer )

We can also note here that secondaries in this transformer design are roughly 1.5 volts per turn. This is a reasonable value for the design. A practical range for secondary volts per turn is usually 1 to 2 volts per turn.

FLYBACK CALCULTIONS - PART III

This post will calculate the current ripple factor from the peak current step IEDC,
the smaller ramp on top of the current pulse which we will call dl, and the RMS current. Fig. 1 shows the general topology of the converter.

First we calculate IEDC

IEDC = Pin / ( Vdcmin * Dmax )

Assume that Pin is 5.8 watts, Vdcmin is 50 volts and Dmax is 86% or 0.86. Calculating IEDC we get

IEDC = 0.135 Amp

This is the first component or major step of the peak current pulse.

The above calculation is the worst case value at maximum duty cycle, maximum input power required, and the worst case minimum input voltage. Note that you will get higher peak currents as D is reduced and Vdcmin is reduced for a given power input value.

We will also calculate the equivalent RMS current, which we will consider below.

Now we need to calculate the second component or ramp of the current pulse, dl

dl = Vdcmin * Dmax / ( Lm * Fs )

Assume that Lm is 0.007 Henry, and Fs is 100KHZ. Then


dl = 0.058 Amp


We can now calculate the Current Ripple Factor, KRF as

KRF = dl / ( 2 * IEDC ) = 0.215

The point of the above calculations is to determine whether the converter will operate in Discontinuous Current Mode (DCM) or in Continuous Current Mode (CCM). When KRF is less than unity, the converter is operating in CCM at minimum voltage input and maximum duty cycle with the specified maximum power input required.

With the results of the above calculations, we can also calculate the equivalent peak current in the transistor switch as

Idspeak = IEDC + ( dl / 2 ) = 0.164 Amp

Next we calculate the theoretical RMS current for the inductor and transistor from


Idsrms = ( 3 * IEDC^2 + dl^2 * ( Dmax / 12 ) )^0.5 = 0.234 watt


This is the current to use when calculating RMS current in the transistor and switching transformer.